The main purpose of this study is to investigate the productivity effects of multiple tree handling in thinnings. Other important elements have been to investigate in which extent multi-tree handling is used in stands with different stem volumes and the impact of collecting partially delimbed fuelwood assortments has on harvesting performance. The study is based on data from thinnings in Sydved and contractors' operating activities. Collection and compilation of operating schedules, number of stems and surveyed volumes from several contractors and a large number of executed orders underlying the results. Multiple tree handling is used to a much greater extent at lower average stem volumes. Prediction models for productivity of the multiple-tree handling harvesters in the study differ from the productivity models for single-tree handling. In the model developed in this study productivity is not as dependent of stem volume as reference models.

The aim for the study was to examine a harwarder´s (combined harvester-forwarder) productivity when harvesting forest fuel in first thinning stands that contains Lodgepole pine and calculate the economy of the harvesting work and estimate the quality of the thinning . The field study area where located near Arvån, about 15 kilometres south ?east from the city of Lycksele. The field studies were taken place in three different stands. All tree stands had the same tree age, but the tree species combination and the density varied.

Profit in first commercial thinnings of today is hard to achieve. This is because of prevailing pulpwood prices and because of high costs of logging and transport. To reduce these costs higher productivity is advocated. One way to increase the productivity is the use of multi-tree handling harvester heads. The aim of this study was to calculate logging and transport costs in first thinnings, where multi-tree handling has been used.

The annual demands for forest fuels increases in Sweden. At present, large unutilized biomass resources is found in young, dense forests from which about five million oven-dry tonnes (ODt) (23 TWh) could annually be extracted as forest fuel. But harvesting small trees give high logging costs and new cost-efficient harvesting techniques are therefore required. The aim was to study the productivity of Vimek 608 BioCombi in forest fuel thinning of Lodgepole pine and to calculate the economy of the harvesting and estimate the thinning quality. The time study was performed in Åmarken in the county of Västerbotten.

The objectives of this research were to determine whether the natural rattan resources in Sulawesi, Indonesia can cope with the strongly increased harvesting pressure that has occurred over the last centuries. I was furthermore looking for patterns in the rattan population dynamics that might give a hint on how the harvesting system could be improved to ensure a maximum sustainable yield. To answer these questions, I developed an individual-based model to analyse the dynamics of rattan growth in connection with rattan harvests by locals to identify sustainable levels of rattan harvests around villages in Sulawesi, Indonesia. Scenarios with different harvesting intensities were run to compare the change in harvest amount. For a given harvesting pressure, scenarios with a high number of harvesters and a low harvesting frequency had the same effect as scenarios with high harvesting frequencies and a low number of harvesters.

The aim for this study where to investigate the frequency of cutting cracks in saw timber harvested in the storm-damaged forests in regions where the storms Hilde and Ivar hit. The idea for this work came from one of the region?s biggest actors, SCA Skog and Jämtlands district. The purpose where to find out how big proportion of the saw timber that contains cutting cracks, their financial cost in lost wood value and also give advice and suggestions on how to work against the frequency of cutting cracks. For the field-study some guidelines where used to make sure that the samples were taken under the same conditions, they were: ? The field-study must be performed under harvesting of storm-felled forest, which are horizontal/inclined trunks. ? The averaged sized tree will make it possible to harvest saw timber. ? The trunks can?t be root cut. A methodology called in Swedish ?Trissmetoden? was used because it is the most frequent used methodology in earlier performed studies and the only one that can be used I field. Under the field-study data were collected from 570 saw timber logs, 30 logs from each one of the tested harvesters.

The aim of this study was to quantify the productivity and the costs of different harvesting systems (teams), containing harvesters equipped with accumulating harvester heads and forwarders, in first commercial thinnings were an integrated harvest of pulpwood and energy wood were performed. In the beginning the plan was to study and measure 20 sites before and after harvest. Due to storms during the summer of 2010, complete data could only be obtained from 8 of these 20 sites. Seven of these sites were privately owned and one was owned by UPM, all of the sites had been pre-commercially thinned. The mean stem density before harvest was 2578 stems per ha and the mean stem volume was 0.074 m3solid over bark.On average 1518 stems/ha was harvested.

I Sverige finns ca 1,2 miljoner hektar skog som bedöms ha omedelbart röjningsbehov. Skog där röjningen uteblir eller är svag kan komma att klassas som konfliktbestånd. I konfliktbestånd är stammarna många och diameterspridningen stor och dessa kan då behövas underröjas innan gallring. I denna studie jämfördes produktionen, kostnaderna och intäkterna från fyra olika underröjningsbehandlingar, oröjd, siktröjt, röjt allt upp till 5 cm i brösthöjd och röjt allt upp till 7 cm i brösthöjd. Behandlingen oröjd gav det bästa nettot och sämst hade upp till 5 cm efter gallring och uttransport av virke.

Stump biomass is energy rich and stump harvesting for use as fuel become more and more interesting in Sweden. Swedish Forest Agency (2009) has estimated that stump harvesting in Sweden would respond to an annual energy supply of 57 TWh/year. However, stump has not been recognized as a bioenergy resource in Sweden. Suitable methods for pre-treatment of stump are probably of great importance to make it accepted as fuel. It is therefore rewarding to carry out an investigation in this area for stump. This report represents results from a diploma project, which was aimed to develop a fixed bed reactor for experimental study of biomass torrefaction, followed by TG analysis and kinetic modelling employing Ozawa method and different kinetic models including one-step and three-pseudo-component models.

Booth for operational planning of harvesting and for long term planning, data is today collected manually. Intensive objective field inventories are usually too expensive. To enhance optimisation of timber flow from forest to industry Moore efficient methods for measuring tree stems of standing trees are needed. The performance of terrestrial laser scanners have improved and these could possibly be used within forestry in the future. The objective of this study was to validate how a terrestrial laser scanner could be used to measure stem diameter, and to test how the errors depend on distance from the scanner and tree species. Two plots (one pine and one spruce) were used for this study.

Low stumps represent on their own up to 80% of the dead wood remaining on clear cuts and therefore supply suitable habitat for saproxylic insects i.e. insects depending on dead wood for their survival. Recent stump harvesting activities threaten this substrate of ecological importance and increase the anthropogenic negative impacts on these species. Because of technical and environmental reasons (nutrient leakage, erosion) guidelines for stump harvesting recommend to retain stumps standing in wet parts of clear cuts. However, stumps in wet positions might not be a satisfactory substrate for saproxylic insects and therefore might not be as much used as stumps in dry positions.

Fortifikationsverket which is the landlord for the Swedish national defence has a great problem in their forestry due to the relatively large amount of metal objects in their timber. These metal objects cause different types of economical losses in the timber refinement chain. To enable out sorting of logs containing metal objects already in the harvesting phase, Fortifikationsverket is interested of the possibility to utilize some type of metal detector in a harvesting head for that purpose.The goal of this study was to, with help of a case study, enlighten the problem that metal objects in timber cause for Fortifikationsverket and their customers of timber and to investigate conditions of to mount and utilize some kind of metal detector in a harvesting head at present.The saw timber deliveries by Fortifikationsverket during the time period 2003-2005 was used as a reference volume for calculations of economical losses. In this case study was included two sawmills where timber from Fortifikationsverket were delivered to for further refinement. Factors investigated were the type of damage metal objects caused in these two sawmills and the economical signification of these damages.

I have chosen in this work to examine which factors are affecting the artificially creation of a tree cavity containing decomposed wood. The purpose of the work is to find out which factors are affecting the most when a tree cavity is created, and to apply these results when you artificially try to create a tree cavity. The need to create tree cavities comes from the situation where many tree cavity living beetles finds themselves today. When existing trees are to pass out there will be no suitable inheritors yet. The work was initially to focus on cavities created from cut branches.

As a student during my studies, I have been told about entrepreneurs who have red numbers in their financial statements, and there is a forest machine operator shortage in Sweden. The basic idea of this thesis was to examine the underlying factors that may have caused the problems described above. The aim of this thesis was to investigate the factors that create stress and job satisfaction as a forest machine operator. The study was performed as a comparison between forest companies own harvesting teams and entrepreneur teams to investigate if there are any differences in stress and job satisfaction between the two different types of team. The study was conducted in collaboration with SCA Skog. The material for this study was collected by doing interviews with SCA's harvesting teams. A total of 27 forest machine operators were interviewed, divided into a total of 10 separate harvesting teams. It was very similar between the different type of teams, which situations the operators experienced stress.

With an increased demand for biomass based energy and with development of better technique harvest biomass, new possibilities open up. With the possibility to combine traditional cleaning of road?s right of way with biomass harvesting, the work of suppressing tree vegetation could become profitable or at least decrease the road maintenance cost. However, knowledge about productivity and profitability in mechanical biomass harvesting in roads? right of ways are still limited.